Belt Conveyor Load Calculation


Advertisement

Beltcomp Nov  v.2007

Beltcomp is a powerful belt conveyor design software program based on ISO/DIN/IS method of calculation using metric units. Beltcomp design program is a highly dependable software to provide consistent, accurate and cost effective belt conveyor designs.

Sidewinder Conveyor Design Software  v.3.0

Software to design belt conveyor systems. Sidewinder was developed from the ground up using the latest software development tools and years of conveyor design experience. It includes: Static calculations, Vertical curve stresses and belt lift off, Horizontal ...





Advertisement

NoVAB 2000  v.2.0.0007

NoVAB 2000 is Nooteboom Vehicle Axle Load Calculation Program.
Is a PC-program for calculating the optimal cargo location on trailers to avoid overload.
In NoVAB-2000 several loads can be placed on one vehicle. The cargo can be positioned one ...

MITCalc - Shafts Calculation  v.1.20

The calculation is designed for geometrical design and complex strength check of shafts.
Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the following
main tasks:
- Simple definition ...

Engineering Power Tools - Plus Edition  v.2.0.4


• Mechanical: belt conveyor calculation, drill sizes, fastener torque, stress and deflection, v-belt drives, and else.
• Electrical: wire tables, Ohm's law calculations, electrical motor, and else.
• Materials: mechanical, physical ...

ComfortAir  v.4.0.1

The application shows versatility in its nature by not only providing the cooling load in a system but also by producing detailed reports and hourly information about the system under consideration. It is a must have for such professionals as architects, ...

Kemper Dendrit Classic  v.5 6

Main features:
- Drinking water pipeline network calculation according to DIN 1988-3, DVGW W 551 a. W 553 incl. Simulation for circulation and KHS
- Wastewater pipeline network calculation acc DIN-EN 12056 a. DIN 1986-100
- Heating: Heating ...

Foundation3D  v.3 40

From equipment-specific automated load calculations to generating design sketches, Foundation3D will increase your productivity significantly at every stage of your project.

Main features:
- International Design Codes: Supports many international ...

LengthWise 2006  v.1.0

LengthWise is the new program that will assist you with the planning of cuts from linear stock materials. Whether you are working with piping, tubing, bar stock, or linear lumber, LengthWise can help you optimize your cuts and minimize materials waste ...

Mine Conveyor  v.3.5.0.15


- Full load is always calculated for comparison.
- User defined idler shape
- Use metric units or U.S. units
- Inputs retained from session to session.
- Shows % of full capacity at design input capacity.
- Material load ...

MITCalc - Rolling Bearings Calculation III (FAG)  v.1 10

This module can be used for the selection, calculation and check of rolling bearings. The programme provides solutions to the following tasks: - Selection and check of a suitable bearing. This module includes a database of approx. 5,000 inch rolling bearings ...

MITCalc - Rolling Bearings Calculation I  v.1.17

This module can be used for the selection, calculation and check of rolling bearings of the company SKF. The
programme provides solutions to the following tasks:
- Selection and check of a suitable bearing. The document includes a database ...

MITCalc - Rolling Bearings Calculation II  v.1.17

This module can be used for the selection, calculation and check of rolling bearings. The programme provides

solutions to the following tasks:

- Selection and check of a suitable bearing. This module includes a database of approx.

MITCalc - Rolling Bearings Calculation III  v.1.15

This calculation can be used for the selection, calculation and check of rolling bearings of the company FAG, INA.

The

programme provides solutions to the following tasks:

- Selection and check of a suitable bearing.

MITCalc - Multi pulley calculation  v.1.18

The calculation is developed for geometrical designs of belt and chain transmissions with more sprocket wheels

(max. 15). Application is developed in MS Excel, is multi-language, supports Imperial and Metric units and solves the

following ...

Pages : 1 | 2 >
Newest Reviews